SR2224P Switch Hardware User Guide

Read about and view specifications and safety guidelines for the SR2224P switch in this topic. Install the SR2224P switch using this topic.

The SR2224P switch offers Gigabit Ethernet switching and advanced features that include static routing, user-based QoS, storm control, 802.1x multiple authentication for voice and data, as well as traditional switching features such as LLDP, Spanning Tree, and IGMP snooping. The SR2224P switch has 24 Ethernet PoE ports, 4x1 Gbps SFP uplink ports and one RJ45 Console port.

For information about how to connect your switch to the network, and for information about Extreme Networks switches in general, see "Introduction to Extreme Switches"

Safety Guidelines

The information in this section applies to all Extreme Networks switch models. The following safety icons identify the type of precaution.

This icon indicates a general caution. Failure to comply with a caution notification can result in damage to equipment.

This icon indicates an electrical caution. Failure to comply with an electrical notification can result in serious injury or death, and extensive damage to equipment.

This icon indicates a laser caution. Failure to comply with a laser caution can result in serious injury.

The following safety precautions apply to Extreme Networks switches:

Do not install the device in an environment where the operating ambient temperature might exceed the recommended ranges.
Make sure the air flow for rack mounted devices is not restricted.
Changes or modifications made to this device that are not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.
The procedures in this manual are for qualified service personnel.
Electrostatic discharge (ESD) can damage equipment and impair electrical circuitry. ESD damage occurs when electronic components are improperly
handled and can result in complete or intermittent failures. Always follow ESD-prevention procedures when handling electronic components.
Make sure the rack or cabinet housing the device is adequately secured to prevent it from becoming unstable or falling over.
Disconnect the power cord from all power sources to completely remove power from the device.
If the installation requires a different power cord than the one supplied with the device, make sure you use a power cord displaying the mark of the safety agency that defines the regulations for power cords in your country. The mark is your assurance that the power cord can be used safely with the device.
The switch must be connected only to PoE networks without routing to the outside plant.
All fiber optic interfaces contain Class 1 lasers. Invisible laser radiation can also be emitted from disconnected fibers. Never look into the end of a fiber, regardless of whether it is active or disconnected.
The optical transceivers used in the SFP port must be laser class I components (under CDRH definition), compliant with IEC/EN60825.

Install the SR2224P Switch

  • Follow the safety guidelines in "Safety Guidelines " to ensure the safety of personnel and equipment.

Install the SR2224P switch on a clean, level desktop or surface, or in a standard equipment rack using the rack mount kit that ships with the switch (see "Rack Mounting Instructions"). If you are installing your switch on a desktop or surface, attach the four rubber feet to the bottom of the chassis to provide stability and prevent the device from moving on the surface.

Rack Mounting Instructions

Use the procedures in this section to mount your device in a standard equipment rack.

For stability, always load a rack from the bottom to the top, with the heaviest devices on the bottom. A top-heavy rack is likely to be unstable and can tip over.
  • Adequate ventilation is critical for switch operation. Install your devices in a properly ventilated equipment rack, or for tabletop installations, leave 2 inches (5 cm) of clear space at the sides of the switch so the fans can properly cool the chassis.

You can mount SR2224P switches in any standard 19" (48 cm) equipment rack. These devices require 1 rack unit (RU) of space, which is 1.75" (44.45 cm) high. Use the following steps to mount the switch in a rack.

  1. Place one of the supplied brackets on the side of the switch so that the four holes of the bracket align with the screw holes on the switch. Use four screws to secure the bracket to the switch. The bracket measurements are shown here:

  1. Attach the other bracket in the same manner.
  2. When the brackets are securely attached, install the switch in the rack using two washers and two rack screws per side, as shown.

Hardware Components

You can see the hardware components for the SR2224P switch in the illustration below, and read about them in the descriptions that follow.

Component Descriptions

Hardware Specifications

The following specifications describe the hardware components, electrical requirements, and the environmental ranges in which the SR2224P can operate.

Device and Enclosure Specifications

  • Chassis dimensions: 17.32” W x 1.75" H x 9.5” D (44.0 cm W x 4.45 cm H x 24.0 cm D)
  • Chassis weight: approximately 8 lb, 2 oz (3.7 kg)
  • 24 IEEE 802.3 (10BASE-T), IEEE 802.3u (100BASE-TX), and IEEE 802.3ab (1000BASE-T) compliant 10/100/1000 Mbps RJ45 Ethernet ports
  • Four 1 Gbps SFP uplink ports

Power Specifications

  • 100-240 Vac, 50-60 Hz, 3.0 A
  • PoE power: 12 ports using 802.3af or 6 ports using 802.3at PoE/PoE+, 180 W

Environmental Specifications

  • Operating temperature: 32° to 104° F (-0 to 40° C)
  • Storage temperature: -13° to 158° F (-25 to 70° C)
  • Operating humidity: 5% to 95% (non-condensing)
  • Altitude: 10,000 ft (3000 m) operating, 13,126 ft (4000 m) storage
  • Low noise: Less than 48 dBA at full power
  • Temperature-controlled fan speed

Regulatory Compliance Statements

The regulatory compliance statements in this section apply to Extreme NetworksAP150W devices.

 


Cloud Terms of ServiceEvaluation AgreementData Privacy and Protection

Copyright ©  Extreme Networks, Inc. 6480 Via Del Oro, San Jose CA, 95119 USA