Hardware and Accessories

Extreme Networks offers a variety of hardware accessories, including non-standard ceiling rack kits for APs and routers, rack-mount kits for switches, and security and power accessories. Extreme Networks accessory kits are described below, with links to the online documents.

Security Bracket Kit for 802.11ac Products

SKU: AH-ACC-SEC-KIT

AP130 Security Bracket Installation Guide

This kit lets you install locking security brackets on ceiling- or wall-mounted 802.11ac wave 2 devices. The kit contains security screws, two locking brackets, and a security screw driver bit. You will need a screwdriver socket that will accommodate the security bit.

Ethernet Protector for Extreme outdoor AP1130

SKU: AH-ACC-1G-ETH-PROT

Ethernet Protector Installation Guide

AP1130 outdoor PoE injectors have built-in surge protection to guard against lightning strikes. However, the point where the Ethernet cable enters the building also requires protection. This kit contains one Ethernet protector to protect the indoor network from power surges caused by lightning.

The following specifications apply to this device:

• 10/100/1000 Base-T Ethernet

• GR-1089 Intra-Building rated

Large Hose Strap kit for AP1130 Outdoor Devices

SKU: AH-ACC-STRP-3-5

This kit allows you to install the AP1130outdoor device on a pole with a 3" to 15" (76 to 381 mm) diameter. The kit contains one large-diameter hose strap.

Plenum and Suspended Ceiling Mounting Kit for AP130 and AP230

SKUs: AH-ACC-BKT-PLENUM and AH-ACC-BKT-SU-KIT

Plenum and Suspended Ceiling Mount Installation Guide

This kit allows you to install APs in the plenum space above a dropped ceiling, or suspend APs from a beam, post, strut, girder, or any object that can support their weight (these devices weigh between 1 and 1.6 lbs, or 0.50 to 0.73 kg). The kit contains a plenum bracket, a hanger clip, the hanger frame, and screws to assemble the frame.

You will need a Phillips screwdriver and pliers to pinch the hanger clip into the mounting bracket.

Recessed Ceiling Mounting Kit for AP130, AP230,and AP250,

SKU: AH-ACC-BKT-80211AC-KIT

This kit allows you to install AP130, AP230, and AP250 devices in dropped ceilings with 3/8”, 9/16”, or 15/16” flushed or recessed ceiling tracks. These devices have built-in mounting hardware to accommodate standard flush 15/16” tracks but require accessory brackets for installation in non-standard dropped ceilings.

You may need a drill and a ladder to install the brackets onto the ceiling track, and to drill a hole in a ceiling tile for cables, if necessary.

Recessed Ceiling Mounting Kit for AP122, AP122X, AP130, AP200 series, and AP500 series (15/16 inch)

SKU: AH-ACC-BKT-80211AC-KIT

You may need a drill and a ladder to install the brackets onto the ceiling track, and to drill a hole in a ceiling tile for cables, if necessary.

Recessed Ceiling Mounting Kit for AP122, AP122X, AP130, AP200 series, and AP500 series (9/16 inch)

SKU: AH-ACC-BKT-80211AC-KIT

You may need a drill and a ladder to install the brackets onto the ceiling track, and to drill a hole in a ceiling tile for cables, if necessary.

Rubber Feet Kit for AP230

SKU: AH-ACC-RBR-FT

This kit contains four self-adhesive rubber feet for use with devices that are installed on horizontal surfaces such as shelves, tables, or desktops.

Silhouette and Interlude-style Ceiling Mount Kit

SKU: AH-ACC-BKT-SLNT-KIT

This ceiling mount kit is designed to attach Extreme APs to Silhouette and Interlude-style ceiling rails. This kit can be used with all APs that have built-in hardware on the bottom of the chassis. The kit contains two brackets (one for each type of rail). The brackets clip onto the AP and the ceiling rail. No additional hardware is necessary. The kit contains detailed installation instructions with measurements that help you determine which bracket to use.

5-GHz Directional Antenna for AP141

SKU: AH-ACC-ANT-4-KIT

This kit contains one 5-GHz 5-dBi antenna and the mounting hardware required to attach it to a wall. The AH-ACC-141-ANT-5 (MARS part number M300310400015) is an indoor dual-band lightweight antenna that is well suited for applications where a 120° H-plane and a 70° E-plane are optimal. These antennas are typically corner-mounted in pairs, facing each other with no obstructions between them.

To install this antenna, you will need a cross-head screwdriver, a drill with a 1/8" (32 mm) bit, a hammer, and an RF test meter for 5-GHz devices.

The following specifications apply to this antenna:

Frequency range: 5.150-5.875 GHz
Bandwidth: 700 MHz
Gain: 2x 5 dBi
Polarization: Dual slant +|- 45°
Width and height: 7.9" (200 mm), depth: 1.25" (33 mm)
Weight: 8.36 oz (260 gr)
Input power, maximum: 20 Watts
Input impedance: 50 Ohms
Operating temperature: -40° to 158° F (-40° to 70° C)
Humidity: ETS 300 019-1-4, EN 302 085 (annex A.1.1)
Environmental compliance: UL94

5-GHz Directional Antenna for AP1130 Outdoor Devices

SKU: AH-ACC-1130-ANT-18

This kit contains one 5-GHz directional point-to-point antenna and the hardware required to install it on a vertical or horizontal pole or mast with a 1.5" to 2" (40 - 50 mm) diameter. You can tilt the bracket to orient the antenna for optimum radio transmission.

To provide unobstructed RF coverage, mount this antenna in a relatively open area on a mast so that it has at least 3' (1 m) of clearance from any nearby obstructions.

The following specifications apply to this antenna:

Frequency range: 5150-5850 MHz

Bandwidth: 700 MHz

Gain: 18 dBi
Width and height: 10" (254 mm), depth: 1.625" (42 mm) without bracket, 8.75" (222 mm) with bracket
Weight: 2.54 lb (1.15 Kg)
Polarization: vertical/horizontal
Maximum power: 20 Watts
(2) N-type female connectors
Ethernet connector: autosensing 10/100/1000 Base-T Mbps; compliant with the IEEE 802.3at PoE standard
Mounting mast diameter: 1.5" - 2" (40 - 50 mm)
Operating temperature: -40° to 140° F (-40° to 60° C)
Storage temperature: -40° to 176° F (-40° to 80° C)
Wind survivability: >165 mph (266 kph)
Environmental compliance: IP67

Dual-Band Sector Antenna for AP1130

SKU: AH-ACC-ANT-SEC

This kit contains a dual-band sector antenna and the hardware required to install it on a pole or mast for use with the outdoor-rated AP1130. The kit also includes four 1 meter (3.25’) RF coaxial cables. To install this antenna, you will need the following tools:

Drive sockets (nut drivers) for 3/8" (10 mm) and 5/8" (16 mm) hex nuts
5/8" (16 mm) open-end wrench to adjust the antenna tilt angle
RF test meter for 5-GHz devices

This kit allows you to install the antenna on posts or masts with a maximum diameter of 1.5" to 2" (40-50 mm). If you want to install this antenna on a pole with a larger diameter, you will also need to order the Large Hose Strap kit (AH-ACC-1130-STRP-3-15).

This antenna should be mounted in a relatively open area with at least 3’ (1 meter) of clearance from nearby obstructions.

The following specifications apply to this antenna:

Width and height: 10" (254 mm), depth: 1.625" (42 mm) without bracket, 8.75" (222 mm) with bracket
Weight: 2.54 lb (1.15 Kg)
Frequency range: 2.4 GHz = 2400 - 2500 MHz, 5 GHz = 5150-5850 MHz
Bandwidth: 700 MHz
Peak gain: 2.4 GHz = 5.0 dBi, 5 GHz = 5.5 dBi
Polarization: ±45°
Horizontal BW 3dB: 120°
Vertical BW 3dB: 2.4 GHz = 80°, 5 GHz = 30°
Front to back ratio: 10 dB
Input impedance: 50 Ohm
Polarization: vertical/horizontal
Maximum power: 6 Watts
(4) N jack connectors
Mounting mast diameter: 1.5" - 2" (40 - 50 mm)
Operating temperature: -40° to 140° F (-40° to 60° C)
Storage temperature: -40° to 176° F (-40° to 80° C)
Wind survivability: 134 mph (216 km/h)
Maximum humidity: 95% at 131° F (55° C)
Environmental compliance: IP-67
Cable loss: 0.66 dB @ 2.5 GHz, and 0.98 db @ 5.0 GHz

Rack Mount Kit for the SR2208P Switch

SKU: AH-ACC-SR-RM-ASM3

The SR2208P switch is a small-format device (approximately 11" wide) designed to be installed on a desktop or other horizontal surface. This kit contains two elongated rack mount brackets and mounting hardware that allow you to install the switch in a standard 19" equipment rack.

Cloud Terms of Service | Evaluation Agreement | Data Privacy and Protection